Bridge Deck Products
Bridge Deck Products & Overhang Brackets
Mily Superior offers an extensive range of bridge deck accessory products, including bridge overhang brackets and interior and exterior bridge hangers. Engineered for performance, Mily Superior is a leader in providing bridge deck product solutions for any size concrete bridge deck project.
C24 – Pres-Steel Half Hanger
C24 45° Pres-Steel Half Hangers are manufactured with a single 1/2″ end section welded to a jogged wire strut and are used where conditions prevent the use of standard double-ended hangers. Standard Style AC hangers measure 12″ from the centerline of the bolt to the end of the strut. This style hanger is designed to be welded to the rebar stirrups of precast concrete bridge beams. Standard Style AS hangers measure 6″ from the centerline of the bolt to the end of the strut.
C25 – Adjustable Half Hanger
The C25 45° Pres-Steel Adjustable Half Hanger consists of a 1/2″ end section welded to a length of 1/2″ diameter Coil Rod, two Stirrup Clips and five 1/2″ Coil Nuts. These hangers are used to support overhang brackets for exterior deck formwork where one-sided forming is required and welding is not permitted.
C41 – Coil Rod Hanger
The C41 45° Coil Rod Hanger is fabricated with a 1/2″ 45° end section welded to the end of a strut that is bent 90° and threaded at the other end. The threaded end of the hanger supports the interior formwork while the end with the 45° end section supports the overhang bracket on the exterior side of the beam. This hanger can accommodate haunch heights of 1/2″ and greater, and comes equipped with a 1″ breakback.
C49 – Bridge Overhang Bracket
Designed with maximum adjustability to meet the varied overhang forming requirements on either structural steel or precast/prestressed concrete beams. Can easily be mounted to steel beams, precast concrete beams and concrete box beams with the appropriate hanger devices
A18 – Panel Bolt
A-18 Panel Bolt is used in conjunction with the A-16 Omni Wedge to fasten adjoining studs. The standard panel bolt accepts two studs dressed to 1-1/2″ each as shown in the sketch. Other sizes are available on special order. A round cut washer should be used under the head of the panel bolt to better distribute the loads.
19 – Corner Washer
A19 Corner Washer is fabricated from 3/16″ x 3″ flat stock bent to form a wedge block. The ample bearing flanges are drilled for nailing to the wales. The A19 Corner Washer accommodates an A9 Tip-To-Tip Tie or a 1/2″ B12 Coil Rod.
A2 – Plastic Cone Snap Tie
A2 Plastic Cones can be added to A3, A4 and A44 Snap Ties and A46 and A48 Loop Ties. The cones act as internal spreaders, reduce grout leakage and aid in the breakback operation.
A21X – Flat Tie
A21X Flat Tie is used with the A51 Wedge Bolt to secure and space modular forms.
A22 – Spreader Cleats
A22 – Spreader Cleats are used to form footers or grade beams up to 32″ high.
A27 – Turnbuckle Form Aligner
The A27 and A27M Turnbuckle Form Aligners are designed to accurately position and plumb vertical forms. The turnbuckle section of the aligner features a 1″ diameter self-cleaning coil thread for fast adjustments.
A27M – Turnbuckle Form Aligner
The A27 and A27M Turnbuckle Form Aligners are designed to accurately position and plumb vertical forms. The turnbuckle section of the aligner features a 1″ diameter self-cleaning coil thread for fast adjustments.
A29 – Snap Tie Shank Wrench
Snap Tie Shank Wrench is designed to facilitate snap tie breakback.
A3 – Snap Tie Heavy
A3 Heavy Snap Ties are used when a higher safe working load is required. The A3 snap tie is manufactured with cold-forged integral heads and is equipped with flats or crimps to prevent turning.
A3 – Snap Tie Standard
A3 Standard Snap Ties are manufactured with either hot- or cold-forged integral heads. A3 Snap Ties have a nominal 1″ breakback with 1/4″ and 1/2″ breakbacks available on special order.
A3 – Snap Tie with Hook
A3 Snap Ties w/ Hook are manufactured with a standard forged head on one end and nut and plate on the other end.
A31 – Wrench Head Snap Tie Socket
A31 – Wrench Head Snap Tie Socket is designed to facilitate A46 Hex Head Snap Tie Breakback.
A3A2 – A3 Standard Snap Tie with A2 Plastic Cone
The A3A2 – A3 Standard Snap Tie with A2 Plastic Cone is manufactured with either hot or cold forged integral heads and features plastic cones that act as internal spreaders to reduce grout leakage and aid in the breakback operation.
A3A46 – Combination Ties
A3A46 Combination Ties are manufactured with a standard forged head on one end and loop on the other end.
A3B1 – Combination Tie
A3B1 Combination Ties are manufactured with a standard forged head on one end and ½” coil tie on the other end.
A40 – Cone Removal Wrench
A40 Cone Removal Wrench is manufactured from high strength steel. It is designed to facilitate plastic cone removal.
A43 – Footing Ties
A43 – Footing Ties are used to form footers or grade beams up to 48″ wide. Footing ties provide economic way to support concrete forms from bowing or collapsing while concrete is being poured.
A44 – Stainless Steel Snap Tie
A44 – Stainless Steel Snap Ties are available for applications that require ties resistant to rusting or other similar corrosion. They are manufactured from type 304 stainless steel wire with button style head.
A45 – Base Tie
A45 Base Ties are used at the base and/or top of modular type formwork. Standard base ties are furnished without cones or breakbacks.
A46 – Snap Ties with Loop
A46 Snap Ties w/ Loop are manufactured with a standard loop on one end and nut and keeper on another end.
A46B1 – Combination Ties
A46B1 Combination Ties are manufactured with a standard loop on one end and 1/2″ coil tie on another. A46B1 Combination Ties are used for connecting Steel-Ply forms to coil rod for blindside wall application.
A4H – Sure-Snap Hex Head Tie
A4H Hex Head Snap Ties are manufactured with hot-forged integral 1/2″ hex-shaped heads. The hex head allows short-end snap ties to be broken back with the formwork still in place.
A5 – Threaded Pullout Tie
A5 – Threaded Pullout Tie is manufactured with a standard forged head on one end and 2″ of 1/4″ – 28 UNF-2A thread on the opposite end. Washers and nut are supplied loose and are placed on the tie after the tie has been installed through the form plywood. A5 ties without spreader washer upsets and washers can be supplied if the internal spreader feature is not required.
A52 – Z Tie Holder
A52 Z-Tie Holder is used in conjunction with the A53 Waler Tie to secure double 2x lumber wales to modular type forms.
A53 – Waler Tie
The A53 Waler Tie is manufactured from high strength steel and is used in conjunction with the A52 Z Tie Holder to secure double 2x lumber wales to modular type forms.
Transform Your Vision
Partner with us to bring your creative ideas to life and transform your business into something extraordinary.
What Our Clients Say
Hear from those who have experienced our exceptional services.
Exceptional service! This company goes above and beyond to meet their customers\’ needs. I couldn\’t be happier with the results.
Your Client 1
Outstanding quality and professionalism. I\’ve been a loyal customer for years and have never been disappointed.
Your Client 2
Reliable and trustworthy. I highly recommend this business to anyone looking for top-notch products/services.
Your Client 3
Impressive attention to detail and excellent communication. Working with this team has been a pleasure.
Your Client 4
Let\’s Create Together
Connect with us to explore how we can make your vision a reality. Join us in shaping the future.